Skip to content

Wookey SDK Dockerfile, to build fully functionnal Wookey build and flash environment

License

Notifications You must be signed in to change notification settings

wookey-project/wookey-docker

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

15 Commits
 
 
 
 
 
 
 
 

Repository files navigation

WooKey SDK Dockerfile

Introduction

this is the Dockerfile for the WooKey project SDK. This image contains a fully functional development environment for the WooKey project, including the overall requested software for building the WooKey firmware and the Javacard applet.

The full WooKey project documentation can be found here:

https://wookey-project.github.io/index.html

In the following, commands starting with host> are made in the host computer, as commands starting with $ are made in the WooKey SDK Docker container.

Building the Docker image

Just run:

host> docker build --tag wookey_sdk --compress <Dockerfile-path>

If you wish to build a Docker image for the nigthly version of Wookey, specify the nightly Docker file:

host> docker build --tag wookey_sdk_nightly --compress -f Dockerfile.nightly <Dockerfile-path>

Running the Docker image

Introduction

A basic start to interactively access the container would be to use: docker run -it wookey_sdk

Although, the SDK is made to build an embedded firmware and to interact with the WooKey boards and Javacard in order to flash them properly. WooKey boards are connected through Discovery board ST-Link USB device, hosting as a CWD probe. Javacard are connected through any USB CCID card reader.

These two devices are real hardware and require multiple USB devices to be accessed from the container. In order to build and flash a WooKey devices in the container require to map them at container start.

This can be done by specifying that USB devices should be mapped into the Docker container:

host> docker run -it --privileged -v /dev/bus/usb:/dev/bus/usb wookey_sdk

CAUTION: this mode makes the docker container being executed in privileged level, as the /dev/bus/usb subtree is fully remapped in the docker container

It is possible to map explicitly each device using the --device option, avoiding a complete remap of the /dev/bus/usb filesystem and a privilegied execution. Nonetheless, the --device arguments depend on your own hardware list (CCID reader, Discovery board ST-Link reference, and so on).

Saving the docker container useful content in the host

You may whish to keep the SDK content (sources, keys, and generated binary files) in the host PC in order to destroy and reinstanciate another container without loosing the useful Wookey files, mostly the crypographic keypairs generated during the first build and used to (un)cypher the Wookey device.

This can be easily done by bind-mounting a given host directory into the container and use it as a storage backend:

host> mkdir /home/john/wookey
host> docker run -it --privileged -v /home/john/wookey:/mnt/backup -v /dev/bus/usb:/dev/bus/usb  wookey_sdk

Here, when entering the container, the /mnt/backup directory exists and can be used by the 'build' user directly. It is then possible to save the private keys after the first build:

$ cp -r private /mnt/backup/private

When restarting another container, it is also possible, before building a new firmware, to get back the previously saved private directory from the backup storage:

$ cp -r /mnt/backup/private private

Knowing that, it is possible to keep the cryptographic content independently of the container lifecycle and to generate new firmwares using the same keypairs. A previously flashed device with a formated SDCard storage can be flashed again without loosing the storage content as there is no key substitution.

CAUTION: In a real, production, mode, the cryptographic elements should be stored securely (software or hardware vault, etc.)

Using the Wookey SDK

Now that the container is up and running and the SDK shell is open, the usual SDK commands can be used, as the overall configuration is already done:

$ source setenv.sh

[...]

$ make defconfig_list

[...]

$ make boards/wookey/configs/wookey2_production_defconfig

INFO: It is possible to update configuration items using:

$ make menuconfig

Typical items are the Javacard PIN values that can be upgraded, in the Secure Token Configuration menu.

Once the configuration is done, it is possible to compile the overall project:

$ make

$ make javacard_compile

All generated files are hosted in the build/armv7-m/wookey subdirectory.

Flashing boards and Javacard from the Docker container

Flashing the board

This is done using OpenOCD:

$ sudo /usr/bin/openocd -f tools/stm32f4disco1.cfg -f tools/ocd.cfg

HINT: If the device is not detected, try to use stm32f4disco0.cfg. The Discovery board device ID may vary.

Flashing the Javacard applets

HINT: You must have an USB Smartcard reader connected to the host which is supported by pcscd.

Javacards access requires PCSC daemon to be started. First, start it:

$ sudo /usr/sbin/pcscd

Considering you have three independent Javacard, you can enter successively a new one after each flashing process. In the case of a debug firmware configuration, it is possible to use a single Javacard for testing purpose.

Enter the Authentication Javacard. Then run:

$ make javacard_push_auth

Enter the DFU upgrade Javacard. Then run:

$ make javacard_push_dfu

Enter the firmware signature Javacard. Then run:

$ make javacard_push_sig

INFO: Beware of killing any instance of the pcscd daemon running in your host PC (i.e. outside the Docker image). The reason for this is that a mutex is locked on the USB smart card reader when an instance of pcscd uses it, so the pcscd running in the host will lock your smart card reader and the pcscd instance running in the Docker image will throw an error when trying to use. On UNIX based hosts, you can kill pcscd either using init.d or systemd services managers, or simply using the kill -9 command as a privileged user.

Booting the device in nominal mode

The device is now ready to be used with its first firmware, flashed using OpenOCD.

At boot time, it requires the AUTH Javacard to be inserted and ask successively for the pet pin (default 1234) and the user pin (default 1337). Once the Authentication process is passed, the device is unlocked and usable as a usual usb mass storage device.

These PIN can be set in the Secure Token Configuration/AUTH Token configuration menu before building the Javacard applet.

They can also be updated at runtime on the WooKey device directly, once it is fully unlocked.

INFO: When booting the device, it may not appear inside the container, as newly hotplugged devices may not have the corresponding /dev/sdX file being created automatically. This does not impact the DFU mode, which can nevertheless be used in the container. In nominal mode although, the device should appear in the host list and be visible in the dmesg messages:

[...]
[ 7404.745045] usb 3-1.4.2.4: new high-speed USB device number 14 using xhci_hcd
[ 7404.846368] usb 3-1.4.2.4: New USB device found, idVendor=dead, idProduct=cafe, bcdDevice= 0.00
[ 7404.846370] usb 3-1.4.2.4: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[ 7404.846371] usb 3-1.4.2.4: Product: wookey
[ 7404.846372] usb 3-1.4.2.4: Manufacturer: ANSSI
[ 7404.846373] usb 3-1.4.2.4: SerialNumber: 123456789012345678901234
[ 7404.849150] usb-storage 3-1.4.2.4:1.0: USB Mass Storage device detected
[ 7404.849315] scsi host3: usb-storage 3-1.4.2.4:1.0
[ 7405.869731] scsi 3:0:0:0: Direct-Access     ANSSI    wookey           0001 PQ: 0 ANSI: 0
[ 7405.870234] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 7405.871469] sd 3:0:0:0: [sdd] 31217152 4096-byte logical blocks: (128 GB/119 GiB)
[ 7405.871778] sd 3:0:0:0: [sdd] Write Protect is off
[ 7405.871779] sd 3:0:0:0: [sdd] Mode Sense: 03 00 00 00
[ 7405.872031] sd 3:0:0:0: [sdd] No Caching mode page found
[ 7405.872035] sd 3:0:0:0: [sdd] Assuming drive cache: write through
[ 7405.881815] sd 3:0:0:0: [sdd] Attached SCSI disk

Signing a new firmware

Once you have compiled a new firmware (using make), and flashed the SIG applet to the Javacard, it is possible to sign it using the Javacard applet as a secure token to encrypt and sign the firmware.

Check that you already started pcscd, or start it:

$ sudo /usr/sbin/pcscd

To sign a new firmware, just run:

$ make sign_interactive tosign=flip:flop version="1.0.0-0"

This command create ciphered and signed version of both A and B (flip and flop) firmware images, with a specific header including the given firmware version.

INFO: This command request the SIG applet Pet PIN and User PIN that have been used at applet compile time. These PIN are the one you set in the Secure Token Configuration/SIG Token configuration menu, or 1234/1234 by default.

Securely update the device

It is possible now to reboot the device in DFU mode (by pressing the DFU button bellow it (little black button). The device boot in DFU mode, which can be distinguished by a violet color style.

The DFU Javacard must be used to authenticate. Again Pet PIN, name and user PIN are the one set in the corresponding configuration menu. Default are 1234/1234.

Once the device has booted in DFU mode, it is possible to update it using the previously generated C+I firmware:

$ sudo /usr/bin/dfu-util -v -D build/armv7-m/wookey/flop_fw.bin.signed -t 4096 -d dead:cafe

The device ask the user to validate the new firmware version, and if it is okay, the firmware is uploaded, authenticated and the device reboots in nominal mode on the newly installed firmware.

About

Wookey SDK Dockerfile, to build fully functionnal Wookey build and flash environment

Topics

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published